General
The SIP Trunk from Voiceworks (DE) was first tested and released with SwyxWare 11.25.0.0.
The SIP Trunk from Voiceworks (DE) is a SIP trunk with user authentication. From the operator portal, you need the channel name to be configured as user ID and user name in the SwyxWare and password.
Platforms
SwyxWare
The SIP Trunk from Voiceworks (DE) can be used without restrictions from SwyxWare 11.25.0.0 on. When using an earlier version of SwyxWare incompatibilities cannot be excluded and use is at your own risk.
SwyxON
The SIP Trunk from Voiceworks (DE) is suitable for central connection in the data center.
Configuration
In the operator portal, the Swyx profile has to be selected. Please be aware that changes in the settings must be reflected by the SwyxWare settings and adopted accordingly.
When creating the SIP trunk group, select the profile 'Voiceworks (DE)'. If an encrypted connection needs to be created, the profile 'Voiceworks TLS (DE)' has to be selected.
SIP URIs
When creating the actual SIP trunk, a SIP URI must be entered after configuration of the phone number range so that incoming calls can be assigned. The assigned number block must be taken into account in the correct format.
Example:
Number block: +49 231 9988776600 ... +49 231 9988776699
In this case, the SIP URI must be entered in the format 023199887766*@*.
Codec configuration
For T.38 FAX transmission, the checkbox "Remove T.38 codec from initial invite" has to be selected in the codec dialog.
Tested features
- Incoming/outgoing national calls
- Incoming/outgoing international calls
- Correct Calling Line Identification (CLI) on national and international calls
- CLIP No Screening
- Holding and retrieving calls
- Toggeling between two calls
- Call transfer
- Conferencing
- Mutually supported codecs: G.722/G.711a/ G.711u/ T.38
- Incoming/outgoing DTMF signaling in accordance with via RFC2833
- T.38 negotiation and FAX transmission
Restrictions
Currently (01/2023) problems may occur with number supression on outgoing call to certain destinations.
Tests
27/01/2023 with SwyxWare 13.25
14/02/2022 with SwyxWare 13.05
12/01/2020 with SwyxWare 12.00.0.0
04/09/2018 with SwyxWare 11.25.0.0
Disclaimer
Verifying interoperability between different SIP providers and the Swyx solution is part of the Enreach Technology Alliance Programme (TAP) tasks. Due to different implementations of the SIP RFCs, it is necessary to determine and provide an individual configuration for each SIP provider.
Within the TAP, Enreach tests a large number of national and international SIP providers in order to make statements about the interoperability with the Swyx solution and the functional scope of the respective SIP trunk. These results and, if needed, configuration advice are published in Help Center articles.
Enreach is in close contact with selected SIP providers to ensure a quick troubleshooting in case of incompatibilities. In addition, tests are repeated at regular intervals to ensure consistent quality.
Despite regular retests it cannot be excluded that incompatibilities with the Swyx solution may occur due to changes in the SIP connection on the provider side or that the provided profile is no longer valid. After creating the trunk group or SIP trunk, the profile settings should be compared with the provider's information and adjusted accordingly in case of deviations.
However, should incompatibilities or problems occur with a tested SIP trunk, no claims for recourse against Enreach GmbH can be derived from this. In such cases, you can contact Enreach Support via your specialist dealer.
The third-party contact information included in this article is provided to help you find the technical support you need. This contact information is subject to change without notice. Swyx in no way guarantees the accuracy of this third-party contact information nor is responsible for it's content.
Comments
0 comments
Please sign in to leave a comment.